0800 043 6728 Email us
Automatic gate maintenance: a Sygma engineer servicing the gate control panel

Gate and barrier maintenance

Automatic gate maintenance

Automatic gate maintenance for commercial sites across the UK: general automatic gate servicing, planned maintenance and 24/7 call-out for swing, sliding and cantilever gates. Whoever installed them.

Gate Safe aware installer. SSAIB certified.

Gate Safe SSAIB certified CHAS accredited Constructionline SafeContractor approved

Why it matters

An automatic gate is machinery. It needs looking after.

An automatic gate moves several hundred kilograms on a schedule set by your site. Without regular servicing, forces drift, safety devices fail quietly and the first warning is a breakdown at the entrance, or worse, an injury.

Planned maintenance keeps the system safe to use, keeps your site accessible and gives you service records that show your insurer, your health and safety advisor and the HSE it is being kept safe.

  • Safety devices tested on every visit
  • Faults found before they stop the gate
  • Service records held for every site you run
Sygma engineer testing the keypad and intercom post of an automatic gate

What a visit covers

Every service visit, end to end

Our engineers work through the whole system, not just the motor, and leave you with a written report of what was tested, what was found and what was done.

Safety devices

Safety edges, photocells and loop detectors tested, checked and realigned so the gate stops and reverses when it should.

Operators and drives

Motors, gearboxes, hydraulic rams and arm mechanisms inspected, lubricated and adjusted, with wear parts flagged before they fail.

Gate leaf and structure

Hinges, tracks, rollers, end stops and posts checked for alignment, wear and corrosion so the leaf runs true and the operator is not fighting it.

Control and access equipment

Control panels, intercoms, keypads, fob readers, ANPR cameras and timers tested, with firmware and settings checked against how the site uses the gate.

Emergency and fire release

Manual release, battery back-up and fire alarm interface tested so the gate opens when it must and can be freed by hand in a power cut.

Signage and documentation

Warning signs and markings checked, then a full service report issued for your compliance file.

What we maintain

Every automatic gate, whoever installed it

We take over systems from other installers and work across the leading operator manufacturers, so one contract can cover every entrance on your estate.

Swing gates

Single and double leaf, with ram and articulated arm operators.

Sliding and cantilever gates

Tracked and trackless gates on rack and pinion drives.

Sliding gate maintenance

High-cycle industrial gates

High-cycle gates on sites that run around the clock.

Operators and controls

Control boards, safety devices, intercoms, keypads, fob readers and ANPR.

Taking over and call-out

Any installer’s gates, 24/7 call-out

Whoever fitted your gates, we can take them on, and one freephone number covers faults at any hour.

The first visit

The first visit is a full survey and safety test of the existing installation. If anything falls short of current standards we tell you plainly, quote for putting it right, and take the system onto a maintenance contract from there.

24/7 call-out

Call 0800 043 6728 at any hour. Out-of-hours attendance is available for gate and barrier faults.

0800 043 6728

Serviced in line with BS EN 12453, HSE guidance on powered gates and Gate Safe guidance. The standards we work to

Get in touch

Put your automatic gates on a maintenance contract

Tell us what you have on site and we will survey it, test it and quote for the maintenance that fits.

Questions

Automatic gate maintenance, answered

Need new or replacement automatic gates?

We design, install and commission them, and strip out old ones.

Automatic Gate Installation
How often should an automatic gate be serviced?

It depends on how hard the gate works. High-cycle sites such as logistics yards need more frequent visits than a gate that opens a few times a day. We set the visit schedule from your risk assessment, cycle count and the manufacturer’s guidance, and write it into the contract.

Can Sygma take over a gate another company installed?

Yes. The first visit is a full survey and safety test of the existing installation. If anything falls short of current standards we tell you plainly, quote for putting it right, and take the system onto a maintenance contract from there.

What happens if the gate fails outside working hours?

Call 0800 043 6728 at any hour. Out-of-hours attendance is available for gate and barrier faults.

Do you maintain the access control and intercom as well?

Yes. Intercoms, keypads, fob and card readers, ANPR cameras and timers are part of the gate system and are tested on every visit.

Is automatic gate maintenance a legal requirement?

Yes, on commercial premises. HSE guidance says owners and occupiers of commercial premises have duties under the Workplace (Health, Safety and Welfare) Regulations 1992, including keeping it maintained, and anyone who works on it must be competent and leave it safe. There is no fixed interval in law, and service records help show it is being kept safe.